cisco_s300#
Warning
This is automatically generated. In case of any issues, please refer to the source code or, even better, open an issue on the GitHub repository. Thanks! 🤗📖
Platforms:#
Commands#
enable#
Output:
null
Help: enter enable mode
Prompt: - cisco_s300>
show mac address-table#
Output:
Flags: I - Internal usage VLAN
Aging time is 300 sec
Vlan Mac Address Port Type
------------ --------------------- ---------- ----------
1 00:08:32:0f:00:61 0 self
300 00:1d:9c:a1:46:86 gi7 dynamic
300 00:1d:9c:a1:50:0a gi8 dynamic
300 00:1d:9c:a1:5b:a6 gi9 dynamic
300 e4:90:69:aa:58:44 gi28 dynamic
400 00:00:bc:39:be:03 gi1 dynamic
400 00:0e:f0:4b:30:02 gi2 dynamic
400 00:0e:f0:4b:30:13 gi2 dynamic
400 00:0e:f0:5a:19:f1 gi27 dynamic
400 00:0e:f0:5a:1a:10 gi3 dynamic
400 00:1d:9c:cd:69:5c gi1 dynamic
400 f4:54:33:91:ea:3a gi2 dynamic
400 f4:54:33:a8:f0:0a gi3 dynamic
Help: execute the command "show mac address-table"
Prompt: - cisco_s300> - cisco_s300#
show vlan#
Output:
Created by: D-Default, S-Static, G-GVRP, R-Radius Assigned VLAN
Vlan Name Ports Created by
---- ----------------- --------------------------- ----------------
1 1 fa1-2,fa4-8,fa10-14, D
fa17-18,fa20
29 29 gi1 S
402 Test-Long-Vlan-Na fa5,gi1 S
me1
3130 3130 fa20,gi1 S
3131 Test-Long-Vlan-Na fa1-2,fa11,fa15-18,fa21-22, S
me2 gi1-4
3132 3132 S
3133 Test-Long-Vlan-Na S
me3
Help: execute the command "show vlan"
Prompt: - cisco_s300> - cisco_s300#
show system id#
Output:
Serial number : IDN123456AA
Help: execute the command "show system id"
Prompt: - cisco_s300> - cisco_s300#
show interfaces status#
Output:
Flow Link Back Mdix
Port Type Duplex Speed Neg ctrl State Pressure Mode
-------- ------------ ------ ----- -------- ---- ----------- -------- -------
gi1 1G-Copper Full 100 Enabled Off Up Disabled Off
gi2 1G-Copper Full 100 Enabled Off Up Disabled On
gi3 1G-Copper Full 100 Enabled Off Up Disabled Off
gi4 1G-Copper -- -- -- -- Down -- --
gi5 1G-Copper -- -- -- -- Down -- --
gi6 1G-Copper -- -- -- -- Down -- --
gi7 1G-Copper Full 100 Enabled Off Up Disabled On
gi8 1G-Copper Full 100 Enabled Off Up Disabled Off
gi9 1G-Copper Full 100 Enabled Off Up Disabled Off
gi10 1G-Copper -- -- -- -- Down -- --
gi11 1G-Copper -- -- -- -- Down -- --
gi12 1G-Copper -- -- -- -- Down -- --
gi13 1G-Copper -- -- -- -- Down -- --
gi14 1G-Copper -- -- -- -- Down -- --
gi15 1G-Copper -- -- -- -- Down -- --
gi16 1G-Copper -- -- -- -- Down -- --
gi17 1G-Copper -- -- -- -- Down -- --
gi18 1G-Copper -- -- -- -- Down -- --
gi19 1G-Copper -- -- -- -- Down -- --
gi20 1G-Copper -- -- -- -- Down -- --
gi21 1G-Copper -- -- -- -- Down -- --
gi22 1G-Copper -- -- -- -- Down -- --
gi23 1G-Copper -- -- -- -- Down -- --
gi24 1G-Copper -- -- -- -- Down -- --
gi25 1G-Copper -- -- -- -- Down -- --
gi26 1G-Copper -- -- -- -- Down -- --
gi27 1G-Combo-F Full 1000 Disabled Off Up Disabled Off
gi28 1G-Combo-F Full 1000 Disabled Off Up Disabled Off
Flow Link
Ch Type Duplex Speed Neg control State
-------- ------- ------ ----- -------- ------- -----------
Po1 -- -- -- -- -- Not Present
Po2 -- -- -- -- -- Not Present
Po3 -- -- -- -- -- Not Present
Po4 -- -- -- -- -- Not Present
Po5 -- -- -- -- -- Not Present
Po6 -- -- -- -- -- Not Present
Po7 -- -- -- -- -- Not Present
Po8 -- -- -- -- -- Not Present
Help: execute the command "show interfaces status"
Prompt: - cisco_s300> - cisco_s300#
show system#
Output:
System Description: 24-Port 10/100 PoE Managed Switch
System Up Time (days,hour:min:sec): 70,03:16:47
System Contact: +7(495)363-06-75
System Name: ZOO-SF300-POE-2
System Location: Moscow, Zoologicheskaya street, room
11
System MAC Address: 34:bd:c8:36:2a:41
System Object ID: 1.3.6.1.4.1.9.6.1.82.24.2
Fans Status: OK
Help: execute the command "show system"
Prompt: - cisco_s300> - cisco_s300#
show ip interface#
Output:
Gateway IP Address Activity status Type
----------------------- ----------------------- --------
10.255.1.51 Active static
IP Address I/F Type Status
------------------- --------- ----------- -----------
10.255.1.72/16 vlan 255 Static Valid
Help: execute the command "show ip interface"
Prompt: - cisco_s300> - cisco_s300#
show interfaces description#
Output:
Port Description
------- -----------
fa1 Test
fa2 Printer
fa3 Socket_7/7
fa4 Socket_7/3
fa5
fa6
fa7
fa8 Camera
fa9 Camera
fa10 Camera
fa11
fa12 Socket_7/2
fa13 Socket_7/4
fa14 Socket_7/8
fa15
fa16
fa17
fa18
fa19
fa20
fa21
fa22
fa23 AP
fa24 AP
gi1
gi2
gi3
gi4 Eltex2124-8 - gi1/0/5
Ch Description
------- -----------
Po1
Po2
Po3
Po4
Po5
Po6
Po7
Po8
Help: execute the command "show interfaces description"
Prompt: - cisco_s300> - cisco_s300#
show interfaces switchport#
Output:
Port : fa1
Port Mode: Trunk
Gvrp Status: disabled
Ingress Filtering: true
Acceptable Frame Type: admitAll
Ingress UnTagged VLAN ( NATIVE ): 203
Port is member in:
Vlan Name Egress rule Port Membership Type
---- -------------------------------- ----------- --------------------
203 203 Untagged Static
222 VOIP-1 Tagged Static
Forbidden VLANS:
Vlan Name
---- --------------------------------
Classification rules:
Mac based VLANs:
Group ID Vlan ID
------------ -------
Help: execute the command "show interfaces switchport"
Prompt: - cisco_s300> - cisco_s300#
show lldp neighbors#
Output:
System capability legend:
B - Bridge; R - Router; W - Wlan Access Point; T - telephone;
D - DOCSIS Cable Device; H - Host; r - Repeater;
TP - Two Ports MAC Relay; S - S-VLAN; C - C-VLAN; O - Other
Port Device ID Port ID System Name Capabilities TTL
--------- ----------------- ------------- ----------------- ------------ -----
gi27 00:08:32:0f:1e:bd gi27 prsw03freeporil B 99
gi28 00:08:32:0f:04:cc gi28 prsw01freeportin B 90
Help: execute the command "show lldp neighbors"
Prompt: - cisco_s300> - cisco_s300#
show version#
Output:
SW version 1.3.7.18 ( date 12-Jan-2014 time 18:02:59 )
Boot version 1.1.0.6 ( date 11-May-2011 time 18:31:00 )
HW version V02
Help: execute the command "show version"
Prompt: - cisco_s300> - cisco_s300#
terminal datadump#
Output: None
Help: Execute the command terminal datadump. This automatically generated. Feel free to change it!
Prompt: - cisco_s300> - cisco_s300#
terminal width 511#
Output: None
Help: Execute the command terminal width 511. This automatically generated. Feel free to change it!
Prompt: - cisco_s300> - cisco_s300#