ubiquiti_edgerouter#
Warning
This is automatically generated. In case of any issues, please refer to the source code or, even better, open an issue on the GitHub repository. Thanks! 🤗📖
Platforms:#
Commands#
enable#
Output: None
Help: enter enable mode
Prompt: - ubiquiti@ubiquiti:~$
show interfaces#
Output:
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 - u/u Port
eth1 192.168.1.1/24 u/u Eth 1
2a05:c100:1d::1/64
eth2 - u/D Port
eth3 - u/D Port
lo 127.0.0.1/8 u/u
::1/128
eth4 192.168.1.1/24 u/u datas
eth4.2900 - u/u
eth5 2a05:c100:1d::1/64 u/u
switch0.1 192.168.10.251/24 u/u vl1-siege-serveurs
Help: execute the command "show interfaces"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show arp#
Output:
Address HWtype HWaddress Flags Mask Iface
192.168.2.10 ether 34:29:8f:76:0f:e8 C eth1
192.168.11.127 (incomplete) switch0.1
172.16.39.98 ether 00:0a:b0:04:98:fb C eth5
172.16.35.123 ether 00:21:b6:00:34:c8 C eth3
172.16.36.200 (incomplete) eth6
172.16.37.165 ether ac:cc:8e:15:a6:3f C eth7
172.16.37.21 ether 90:b1:1c:2f:92:82 C eth7
Help: execute the command "show arp"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show dhcp leases#
Output:
Warning: leased IP address [2886804269] not in any of the pools
Warning: leased IP address [2886804283] not in any of the pools
Warning: leased IP address [2886804287] not in any of the pools
Warning: leased IP address [2886804295] not in any of the pools
Warning: leased IP address [2886804284] not in any of the pools
Warning: leased IP address [2886804252] not in any of the pools
Warning: leased IP address [2886804248] not in any of the pools
Warning: leased IP address [2886804305] not in any of the pools
IP address Hardware Address Lease expiration Pool Client Name
---------- ---------------- ---------------- ---- -----------
125.125.15.12 00:0a:95:9d:68:16 Sep 18, 2021 5 HOSTNAME
Help: execute the command "show dhcp leases"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show dhcpv6 server leases#
Output:
There are 6 DHCPv6 leases:
IPv6 Address Expiration State
--------------------------------------- ------------------- ------
2001:d98:5554::210 2014/01/27 18:55:53 active
2001:d98:5554::212 2014/01/27 19:46:12 active
2001:d98:5554::213 2014/01/27 19:00:18 active
2001:d98:5554::225 2014/01/27 20:31:06 active
2001:d98:5554::214 2014/01/27 18:55:57 active
2001:d98:5554::219 2011/06/01 06:02:16 expired
Help: execute the command "show dhcpv6 server leases"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show ipv6 neighbors#
Output:
2a01::68e5:a41e:722c:2f7b dev eth0 lladdr 6c:40:08:4f:35:bc STALE
fe80::7e91:22ff:fe87:d336 dev eth0 lladdr 7c:91:22:87:d3:36 STALE
fe80::feec:daff:fe47:bf49 dev eth0 lladdr fc:ec:da:47:bf:49 router STALE
fe80::250:56ff:fe90:50ee dev eth4.51 lladdr 00:50:56:90:50:ee router REACHABLE
fe80::11:32ff:fe2a:c970 dev eth1 lladdr 02:11:32:2a:c9:70 STALE
2a05:c100:37:0:6d40:4b07:e518:9ada dev switch0.1 FAILED
fe80::be16:65ff:fe7e:1cc1 FAILED
2a02:33:44::1 router INCOMPLETE
fe80::d093:e5ff:fe8e:8427 lladdr d2:93:e5:8e:84:27 STALE
2a02:33:44::12 lladdr d2:93:e5:8e:84:27 STALE
fe80::be16:65ff:fe7e:1cc1 lladdr bc:16:65:7e:1c:c1 DELAY
2a02:33:44::1 lladdr bc:16:65:7e:1c:c1 router REACHABLE
fe80::d093:e5ff:fe8e:8427 lladdr d2:93:e5:8e:84:27 STALE
2a02:33:44::12 lladdr d2:93:e5:8e:84:27 STALE
Help: execute the command "show ipv6 neighbors"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show interfaces ethernet physical#
Output:
Settings for eth0:
Auto-negotiation: off
Speed: 1000Mb/s
Duplex: Full
Link detected: no
Help: execute the command "show interfaces ethernet physical"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show ipv6 route#
Output:
IPv6 Routing Table
Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,
IA - OSPF inter area, E1 - OSPF external type 1,
E2 - OSPF external type 2, N1 - OSPF NSSA external type 1,
N2 - OSPF NSSA external type 2, B - BGP
Timers: Uptime
IP Route Table for VRF "default"
S ::/0 [50/0] via ::, pppoe4, 01w0d05h
S ::/64 [50/0] via 2a05:c100:1d::2, eth1, 00:00:04
C ::1/128 via ::, lo, 01w0d05h
C 2a05:b780:0:1d::/64 via ::, pppoe4, 01w0d05h
C 2a05:c100:1d::/64 via ::, eth1, 01:11:26
C fe80::/10 via ::, pppoe4, 01w0d05h
C fe80::/64 via ::, eth1, 01:11:25
Help: execute the command "show ipv6 route"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show nat rules#
Output:
Type Codes: SRC - source, DST - destination, MASQ - masquerade
X at the front of rule implies rule is excluded
rule type intf translation
---- ---- ---- -----------
1 DST pppoe4 daddr 23.90.233.198 to 192.168.1.100
proto-tcp dport 8080 to 80
2 DST pppoe4 daddr 23.90.233.198 to 192.168.1.231
proto-tcp dport 65001 to 3389
3 DST pppoe4 daddr 23.90.233.198 to 192.168.1.2
proto-tcp dport 6666 to 6666
4 DST pppoe4 daddr 23.90.233.198 to 192.168.1.111
proto-tcp_udp dport 83 to 83
5 DST pppoe4 daddr 23.90.233.198 to 192.168.1.110
proto-tcp_udp dport 80 to 80
6 DST pppoe4 daddr 23.90.233.198 to 192.168.1.1
proto-tcp_udp dport 81 to 81
5001 MASQ pppoe4 saddr 192.168.1.0/24 to 23.90.233.198
proto-all sport ANY
5002 MASQ pppoe4 saddr 192.168.42.0/24 to 23.90.233.198
proto-all sport ANY
Help: execute the command "show nat rules"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show ip route#
Output:
Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
> - selected route, * - FIB route, p - stale info
IP Route Table for VRF "default"
S *> 0.0.0.0/0 [50/0] is directly connected, pppoe4
S *> 22.22.23.0/24 [1/0] via 198.168.0.1 (recursive is directly connected, pppoe4) )
S *> 23.23.23.0/24 [1/0] via 198.168.0.1 (recursive is directly connected, pppoe4) )
C *> 23.90.232.243/32 is directly connected, pppoe4
S *> 25.22.23.0/24 [35/0] via 198.168.0.1 (recursive is directly connected, pppoe4) )
C *> 100.95.11.96/32 is directly connected, pppoe4
C *> 127.0.0.0/8 is directly connected, lo
S *> 192.100.111.0/24 [1/0] via 192.168.1.25 (recursive is directly connected, pppoe4) )
*> [1/0] via 192.168.1.20 (recursive is directly connected, pppoe4) )
Help: execute the command "show ip route"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
show version#
Output:
Version: v2.0.6
Build ID: 5208554
Build on: 07/08/19 06:11
Copyright: 2012-2018 Ubiquiti Networks, Inc.
HW model: EdgeRouter 6P
HW S/N: FCECDA47BF8A
Uptime: 16:17:57 up 11 days, 6:15, 1 user, load average: 0.09, 0.06, 0.01
Help: execute the command "show version"
Prompt: - ubiquiti@ubiquiti:~$ - ubiquiti@ubiquiti:#
terminal length 0#
Output: None
Help: Execute the command terminal length 0. This automatically generated. Feel free to change it!
Prompt: - ubiquiti_edgerouter> - ubiquiti_edgerouter#
terminal width 512#
Output: None
Help: Execute the command terminal width 512. This automatically generated. Feel free to change it!
Prompt: - ubiquiti_edgerouter> - ubiquiti_edgerouter#